Enzotech Extreme-X REV.A Bedienungsanleitung PDF herunterladen

Extreme-X COOLER SUPPORT

1.Dimension: 148*148*118mm

2.Total weight : 835g

3.Fan: Fan AD1212UB-A73GL

Dimension 120*120*25mm

Speed 2500R.P.M

Noise 43.3 dB-A

Air Flow 98.6 CFM

Voltage 12VDC . 0.5A

Connector Molex 2695- 3 wire

Bearing 2 ball

UL ,CUL , TUE and CE approval

4.Heat sink Forge C1100 copper base , mirror polish

Aluminum pin fin heat sink

4 piece of 8Ø pipes

Aluminum radian fin

5.Thermal grease Arctic Sliver 5

6.Speed controller Speed 1200R.P.M 1800R.P.M 2500R.P.M

Noise 25.5 dB-A 31.5 dB-A 38.5 dB-A

Air Flow 35.8 CFM 53.6 CFM 82.67 CFM

1.Features

(1) Compatible with all single and dual core CPUs for

Intel Socket 775 and AMD Sockets K8/AM2/754/939/940

(2) The base of the Heat Sink is machined to 0.0003 per inch run-out

which optimizes surface contact and maximizes thermal conductivity

perforrmance.

(3) Four 8mm heat pipes guarantee the CPU will always run smooth and

at optimum effciency.

(4) The large 120mm fan provides extreme colume of airflow which will

keep your Northbridge chipset cool at the same time

(5) Arctic Silver 5 Thermal Grease and Adjustable fan speed control include.

3.Components

1)Common Components

a)One(1) User’s Manual

b)One(1) AS5 Thermal Grease

c)One(1) Fan controller

d)One(1) Knob

e)Two(2) Bolts for fixing Fan

Controller

f)One(1) Extreme-X Cooler

2)Components for Socket 754/939/940/AM2

g)One(1) Backplate for Socket 754/939

h)One(1) Retention Module

i)Two(2) Clip Bolts

j)One(1) Clip Lever

3)Components for Intel Pentium 4 Socket 775

k)Four(4) Innerspring Screws

l)Four(4) Plastic Washers

m)One(1) Backplate for Socket 775

(2)AMD Socket k8/754/939

Remove the original Clip support for AMD “Socket k8/754/939”

from the Motherboard.The clip Enzotech provides is thinner at the

edges.Users of AMD “Socket k8/754/939” MUST CHANGE THIS

CLIP. The CPU cannot make contact with the top of the cooler

using the original clip!

3. Hold attachment lever upright, then press

down (1) and move it outwards (2) until

the clip slots fit on to the Retention Module

lugs.

4. Make sure slots of retaining clip are firmly

attached to the retention module lugs on

both sides, then fasten the lever in place as

shown.

(3)AMD Socket AM2/940:

4. Align the slots in the retaining clip with the

lugs on the retention module (1). Then

rotate cooler down until it sits horizontally

on the CPU (2).

2. Clean the contact surfaces of the CPU

and heatsink. Then apply “Arctic Silver 5”

on the contact surface of the CPU and

the heatsink base.

(1)Intel Pentium 4 -775

1. Clean the contact surfaces of the CPU and

heatsink. Then apply “Arctic Silver 5” on the

contact surface of the CPU and the heatsink

base.

2. Align back plate for “Socket 775”

on back side of the motherboard.

3. Place Extreme-X on the center of the

CPU. There are four holes on the

base to put the metal rods through.

4. Place innerspring screws on the

four metal rods and fasten down

until all sides are level.

3. Hold the attachment lever upright, then

press down (1) and move it outwards (2) until

the clip slots fit onto the Retention Module

lugs.

2. Plug other end of fan speed connector into

the 3-pin CPU fan connector on the

motherboard

3. Install the bracket of the fan-speed

controller in an open PCI slot.

4. Push the knob in place

Note:

Some mainboards will not boot if rotation of the CPU fan is below a

certain number of RPM’s. If this happens, try changing the BIOS

setting to “Silent Mode”.For more information on updating BIOS,

please refer to your mainboard installation manual or the

manufacturer's web site.

1. Align the Retention Module and the back-plate

for AMD “Socket k8/754/939” with the

mounting holes on the motherboard and

fasten them together using the Retention

Module mounting bolts.

Precautions:

1.Excessive force exerted on fan assy during installation can

damage the fan,resulting in damage to the system.

2.Avoid inserting any objects into the fan while it is in operation.

3.Check the parts list and condition of product before installation.

If any problem is found, contact place of purchase to obtain

replacement.

4.Do not ingest or make oral contact with the Thermal Grease.

If ingested, get medical attention immediately.

5.Enzotech is not responsible for any damages due to external

causes, including but not limited to, improper use, problems with

electrical power, accidents , neglect, alteration, repair, improper

installation, or improper testing.

2 Align the slots in the retaining clip with the

lugs on the retention module (1), then rotate

cooler down until it sits horizontally on the

CPU (2).

1. Clean the contact surfaces of the CPU

and heatsink. Then apply “Arctic Silver 5”

on the contact surface of the CPU and

the heatsink base.

1. Plug adjustable fan speed connector into

the 3-pin connector of fan as shown in

Figure 1.

(4)FAN Speed Controller

1 2 3 4 5 6 7 8 9

4.Installation

2.Specifications

*Power Connection

Please refer to Fan Speed Controller Installation on page ( 8 )

*Power Connection

Please refer to Fan Speed Controller Installation on page ( 8 )

*Power Connection

Please refer to Fan Speed Controller Installation on page ( 8 )

*Please read this manual thoroughly before installation

User’s Manual

(English Version)

http:// www.enzotechusa.com http://www.enzotechnology.com

*Please read this manual thoroughly before installation

User’s Manual

(English Version)

http:// www.enzotechusa.com http://www.enzotechnology.com

User’s Manual 1

Inhaltsverzeichnis

Seite 1 - User’s Manual

Extreme-X COOLER SUPPORT1.Dimension: 148*148*118mm 2.Total weight : 835g 3.Fan: Fan AD1212UB-A73GL

Kommentare zu diesen Handbüchern

Keine Kommentare

Enzotech Extreme-X REV.A Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Spülung Enzotech Extreme-X REV.A herunter. EnzoTech Extreme-X REV.A User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern